Made by a union worker, for union workers.
Everything you logged is kept and comes back the moment a key is activated. One licence opens everything: the cheque calculator, hours log, year log, calendar, trade info and every employer, $4.99 a year. One key works on up to three phones.
| Day | Hours | Stat | LOA | Night | Alloy | Paid as |
|---|---|---|---|---|---|---|
| Week |
Every day you logged is kept. A licence opens the year log, the calendar, the by-employer and by-month totals and every employer, along with everything else. $4.99 a year, one key for up to three phones.
| Week | Hours | Gross | Tax | Take-home |
|---|
| Employer | Hours | Gross | Tax | CPP | EI | Pension | Take-home |
|---|
| Month | Hours | Gross | Tax | CPP + EI | Take-home | Allowances |
|---|
Log your hours day by day and see every cheque: straight time, time and a half, double time, vacation and holiday pay, dues, CPP, EI, an income-tax estimate and living-out. The year view adds it all up. Built for crane operators across Canada: Alberta Local 955 (the CLR-A general construction agreement, Part A industrial with its crane tonnage table, Part B commercial and the civil enabled rates, and the GPMA / NMA maintenance rows), British Columbia Local 115 (the CLR-BC crane rental and steel erection agreements, conventional and hydraulic cranes by tonnage), Ontario Local 793 (Schedule A crane rental and the Schedule J GTA building schedule, inside and outside Board Area 8), Quebec's grutiers under the sector conventions (the 13% banked at the CCQ and Quebec tax), Manitoba Local 987 (CLRAM tower and mobile cranes) and Nova Scotia Local 721 (the Cape Breton industrial and commercial appendices). Pick your crane on the Settings tab: the classification list is the crane picker, by type and tonnage, with the oilers, signal persons, crane apprentices and foremen that go with the crane, and the rate follows the crane you pick (pick another one under any day you ran a different crane). Heavy-equipment (non-crane) rates and crane rental (ACOA) rates aren't in yet: send us your agreement. Each agreement comes with its own payroll tax. The week shown first is an example; change any box.
These come from the TD1 forms you filled in for this employer. Most people claim the basic amounts. Your pay stub may list them as "TD1 claim" or "claim code".
From the W-4 you gave this employer, and your state's withholding form. With no W-4 on file, payroll withholds as single with nothing else claimed.
Step 4b is where the new deduction for overtime goes if you claim it on your W-4: only the half-time part of hours over 40 a week counts, not daily overtime or the extra half of double time.
Only if your stub shows one. Enter a percentage of pay or a flat amount a week, for example NYC, Yonkers, a Pennsylvania earned income tax, an Ohio or Michigan city, Kansas City or St. Louis, or a Kentucky occupational tax.
Pass it on, get a free month. Every mate who buys a licence through your code or link adds a free month to yours, up to a year. They point their phone camera at this code and tap the link that pops up, or you send them the link:
On the home screen it opens full screen, works without signal, and your log stays on the phone and is never uploaded.
One licence, $4.99 a year, opens everything: the cheque calculator, hours log, year log, calendar, trade info and every employer. Your key is tied to your email address and works on up to three of your own phones.
Your log is saved on this phone or browser only. Copy a backup now and then and keep it in your notes or email it to yourself. Paste it back here to restore, or to move to a new phone.
A number that doesn't match your stub, a rule we got wrong, something you'd like added. Say which agreement and classification. Email is optional; leave it if you'd like a reply.
Agreement missing from the app, or newer than the one in here? Send the PDF or Word file, or photos of the wage pages. It's only used to add the agreement to the app. The files are deleted within 90 days of when you send them. If the app doesn't have that agreement yet, you get a free year when it's added.
Trade info comes with the licence, along with everything else.
ASME B16.5 flanges. Stud lengths are the standard's: the raised face is 1/16" on Class 150 and 300 and 1/4" on Class 600 and up. The flat gasket is a ring gasket to ASME B16.21 (spiral wound gaskets are sized differently). The wrench is the heavy-hex nut across the flats. The drawing and the job's bolting procedure come first.
Flanges are two-holed: bolt 1 sits just clockwise of the top, level with the last bolt. Going clockwise from 1, mark the bolts in this order:
Then tighten in number order: 1, 2, 3, 4 and so on. Each odd and even pair sits straight across the flange. With two wrenches, do 1 and 2 together, then 3 and 4. Bring it up in passes; the job's procedure sets how many. This is the cross pattern in ASME PCC-1.
B7 studs (ASTM A193) with heavy-hex nuts, torqued to load the stud to half its yield strength, with C5A or a dope like it on the threads and nut faces (friction 0.10). B7 is rated lower above 4", so a 4 1/4" stud takes less torque than a 4". These are guidelines only: the manufacturer's spec or your engineering department comes first.
Enerpac RSL2 to RSL30 (hex or square drive; current model names in brackets) and S1500X to S11000X (square drive). HYTORC Stealth (hex) and Avanti, MXT and ICE (square drive). Type a torque to get the pump pressure, or a pressure to get the torque. Between the chart's rows it's worked out in a straight line. These are the makers' standard charts (Enerpac's instruction sheets, HYTORC's conversion charts); your wrench's own calibration certificate comes first.
L is one sling (or one side of the basket), from the hook to where it meets the load. S is straight across between where the two sides meet the load. Use the same units for both (feet or inches). Keep the slings above 30°; 60° is best. This assumes the hook is over the centre of gravity. Each sling's tag rating for its hitch has to cover the pull.
Melloy wire rope slings (PCL's rigging card): improved plow steel, IWRC (6x19 up to 1 1/8", 6x36 from 1 1/4"), eyes and thimbles in both ends, Flemish spliced eyes with mechanical sleeves, safety factor 5. Basket is both legs straight up; a double basket is twice that; for an angle, use Sling tension. Choker ratings need a choke angle of 120° or more. Extra improved plow steel (EIPS) slings rate about 15% higher; the tag tells you which you have. Never rig below 30° from horizontal. Fibre-core rope rates lower. The tag on the sling comes first.
A ply is a layer of webbing. 2-ply is the everyday sling; 1-ply is a lighter version rated about half, so check which you have: the tag says, and on many makers' part numbers EE1 means 1 ply and EE2 means 2 ply. Lift-All Webmaster 1600 nylon eye-and-eye slings (1,600 lb per inch per ply; polyester in this line rates the same). Keep nylon away from acids and bleach, and don't use it above 90 °C (194 °F). Pad sharp edges. The tag on the sling comes first.
Melloy card: forged alloy steel shackles, straight-line pull. Pulled from the side a shackle holds less: 70% of its rating at 45° and 50% at 90° (Crosby). Never replace a shackle pin with a bolt; the load will bend it. These run about 10% under Crosby's current ratings. The rating stamped on the shackle comes first.
Never saddle a dead horse: every U-bolt goes on the dead end, and don't stagger the clips. Use drop-forged clips, not cast. Torque is for clean, dry threads. Add one clip if the rope turns over a sheave instead of a thimble, and one for Seale-type rope 1" and up. Crosby's table (G-450). It matches the Melloy card except that it calls for one more clip at 1 1/4" and 1 1/2". Follow the clip maker's instructions.
1 in = 25.4 mm exactly. 1 ft-lb = 1.3558 N·m. 1 psi = 6.8948 kPa. 1 lb = 0.45359 kg. 1 US gal = 3.7854 L, 1 Imperial gal = 4.5461 L. 1 kip = 4.4482 kN.
Everything below is for the employer picked on the Settings tab. Rates step on the agreement's own dates and the calculator uses the column in force for the week you're looking at. Hours are your hours on site, breaks included, the way the agreement's overtime rules count them.
Not included: heavy-equipment (non-crane) rates and Alberta crane rental (ACOA) rates; send us your agreement (Settings tab). This is a crane operator app: the dozer, grader, loader, excavator, roller and paver classes, mechanics and welders, and Quebec's heavy-equipment and shovel operators aren't offered. The Alberta Crane Owners Association agreement 2025–2029 (about 1,200 operators) publishes only its settlement percentages, not the wage schedule. Also not public: Saskatchewan Local 870 (the CLRS copies are redacted), Newfoundland and Labrador Local 904 (the wage appendix is blank), New Brunswick Local 946 and PEI Local 942 (only expired texts), the Nova Scotia mainland crane and earth-mover agreements (expired April 30 2026, no renewal posted), BC Heavy Construction 2026–2029, the Manitoba crane rental division, the PLCAC pipeline and the roadbuilding agreements, and the territories. Not modelled: travel time and mileage (enter them on the Week tab), call-outs and show-up pay, the 10-and-4 and other rotations outside the GPMA blended rate, two premiums at once on the same crane, first-aid and underground premiums, Quebec isolated sites (B-1) and the civil-engineering (GCV) and residential sectors, and living-out or travel amounts that step mid-agreement (change the amount in Settings on the date). No local publishes its monthly dues: enter them from your stub. Employer pension, health and training contributions aren't on your cheque; the pension part is shown as a memo line under the cheque and on the Year tab.
Yours missing? Send it from the Settings tab (Send us your agreement). If the app doesn't have it yet, you get a free year when it's added.
Made by a union worker, for union workers. Independent tool. Not affiliated with any union: not made by or affiliated with the International Union of Operating Engineers or any of its locals, FTQ-Construction or any other union or council, any employer bargaining association (CLR Alberta, the Alberta Crane Owners Association, CLR-BC, the Ontario operating engineers' employer bargaining agency, CLRAM, NSCLRA, the ACQ and others), the CCQ, the National Maintenance Council, any crane rental company or any contractor. This is an estimate, not payroll advice. Your stub and your steward have the final word.
Your hours, pay, employers and settings stay on this phone. There's no account and no sign-in, and we never see your log.
What we do receive:
We don't sell or share any of it, and there are no ads or tracking scripts. The site is hosted by Cloudflare and payments go through Stripe. They see what any web host or card processor sees.
To see or delete what we hold about you, send a note through the feedback box with your key or email.
© 2026 TradesPay. All rights reserved.